| Command |
Description |
3152A
Limitations (if any) |
| AM |
Set
external modulation to AM and set the AM modulation index. |
Not
implemented. |
| AMPL |
Specify
the amplitude of the function output. |
No
restrictions. |
| AMPL? |
Query
the amplitude of the function output. |
No
restrictions. |
| BRST |
Set
the burst count. |
No
restrictions. |
| BRST? |
Query
the burst count. |
No
restrictions. |
| BUF |
Place
the module in buffered mode. |
No
restrictions. |
| DAT |
Load
data into the module for use in generating arbitrary waveforms. |
No
restrictions. |
| DFREQ |
Change
the output by the specified amount, phase continuously. |
No
restrictions. |
| DINT |
Disable
VXI Interrupt generation. |
No
restrictions. |
| DPHAS |
Change
phase of output by the specified amount, phase continuous. |
No
restrictions. |
| ERR? |
Query
for error conditions. |
No
restrictions. |
| FILT |
Enable
or disable a low pass filter to the output waveform. |
VX4750:
12MHz filter selected 3152A: 20MHz filter selected. |
| FM |
Set
external modulation to FM and set the FM peak deviation. |
Not
implemented. |
| FREQ |
Specify
the frequency of the output waveform. |
No
restrictions. |
| FREQ? |
Query
the frequency specified in last valid FREQ command. |
No
restrictions. |
| FSK |
Set
external modulation to FSK and set the FSK frequencies. |
Not
implemented. |
| FSK? |
Query
the FSK frequencies. |
Not
implemented. |
| IMP |
Specify
the load impedance connected to the arb. |
No
restrictions. |
| INT |
Enable
VXI event generation from the module. |
No
restrictions. |
| IST |
Initiate
a self-test |
3152A
error codes are returned. |
| ISWP |
Specify
internal linear sweep parameters. |
VX4750:
1mHz to 10MHz/7MHz to 25MHz 3152A: 1mHz to 10MHz |
| LSWP |
Specify
internal log sweep parameters. |
VX4750:
1mHz to 10MHz/7MHz to 25MHz 3152A: 1mHz to 10MHz |
| NBUF |
Place
the module in non-buffered mode. |
No
restrictions. |
| OFST |
Specify
the DC offset of the output waveform. |
No
restrictions. |
| OFST? |
Query
the DC offset of the output waveform. |
No
restrictions. |
| PHAS |
Specify
the phase of the output waveform. |
No
restrictions. |
| PHAS? |
Query
the phase of the output waveform. |
No
restrictions. |
| PM |
Set
external modulation to PM and set the max PM phase deviation. |
Deviation
not settable. Lock signal must be provided. |
| PSK |
Encode
data on the output waveform using PSK modulation. |
Not
implemented. |
| PWM |
Set
external modulation to PWM and set max DC deviation from 50%. |
Not
implemented. |
| REFI |
Selects
a frequency reference source. |
No
restrictions. |
| REFO |
Selects
10MHz or 33MHz to be output to the REF OUT connector. |
Not
implemented. |
| REV? |
Return
the firmware revision. |
Returns
the 3152A firmware revision. |
| RST |
Reset
the module to its power-up state. |
No
restrictions. |
| SPER |
Specify
the sample period to use to generate arbitrary waveforms. |
No
restrictions. |
| SPER? |
Query
the sample period used to generate arbitrary waveforms. |
No
restrictions. |
| SWP
OFF |
Disable
sweep. |
No
restrictions. |
| TRGI |
Select
a trigger input source and polarity of front panel trigger. |
No
restrictions. |
| TRGO |
Select
trigger output and polarity of front panel trigger output. |
No
restrictions. |
| TRIG |
Trigger
the module to output a pre-defined waveform. |
No
restrictions. |
| XSWP |
Set
to external sweep and define start/stop frequencies. |
Not
implemented. |
| XSWP? |
Query
the start/stop frequencies of external sweep. |
Not
implemented. |
| WAVE |
Specify
the type of function generator waveform used. |
No
restrictions. |
